How fast do bowling balls roll

When you get to a point where you are no longer able to maintain a fast ball speed, you should opt for the most speed that you can comfortably sustain and still maintain balance on the lanes. If you want to hit the ball with more speed, think about how high you hold it. The higher you hold the ball, the faster it will be. Usually, people use a set-up position where they hold the ball at their waist level. You can increase your speed by holding your ball at shoulder level.

If you normally hold it at knee level, then at least try to move it up to waist level. Start your approach with a gradual, rolling arc-shaped motion. Slowly move your arm out until it is fully extended to create greater downswing and backswing momentum. Avoid extending your arm too far forward because that can throw off your shoulder position. Simply keeping your shoulder in position and using the natural extension of your arm as a lever will give you the momentum needed when swinging the ball.

Allow the ball to swing freely to the top of your backswing and again on your forward swing. As you get faster, move your feet along with your swing to maintain a good tempo. Losing ball speed can be caused by tension in your arm and legs. In order to maintain increased ball speed and make consistent deliveries of the bowling ball, you must use tension-free arm swing motion throughout the entire release position.

Ball speed control is essential to determining how far a ball will skid. When you release the ball, you should maintain a constant spine angle during your approach and delivery motion. There are a few other important factors that could help improve your game: reduce bowling arm, neck, and shoulder tension as much as possible. Two Important things to keep in mind when thinking about ball speed are lane conditions and your rev rate.

For lighter oily lanes, a ball that is too fast may not stay on the lane as well, which can cause it to miss the pocket. The lane conditions are the most important factor in determining how fast a bowler can throw his or her ball down the lane.

The faster you roll your ball, the more likely it is that you will be able to get strikes on any given shot. In your next practice session, try letting your lower body movement and momentum help you attain more speed. Try moving back slightly on the approach and work on gradually increasing your foot speed to the line.

Feel your feet drive you forward into your slide a little more aggressively. This should make it easier to maintain accuracy as you begin to get that extra speed from your lower and upper body. Timing and other factors also play a role in attaining more ball speed efficiently. Proper timing, armswing direction, etc.

There really is no substitute for efficient motion. The best thing to do is to be honest about your game. That may seem like a rude comment but it is not intended to be. The reason I say that is because I see many bowlers drill balls in an attempt to cover up weaknesses.

You must know what in your game you do well and what needs work. Many bowlers have only high friction equipment in their bags because they are only looking for the most overall hook potential. Oil patterns constantly change starting from the very first warm up shot until the last shot is thrown. The surface of the ball controls when it slows down. My suggestion would be to keep it simple. Most of the best players in the world use only a couple of different layout techniques for the majority of their equipment.

Granted, if they need something specific, they certainly have the means to try it. But for most of their arsenal, you will see a lot of the same drill patterns, just on different pieces of equipment. Find two or three layouts that work best for your game and then stick with those on any new balls you may drill. So, what new balls should you drill?

Well, research the balls you have liked in the past and see what their manufacturing specs are RG, differential, out of the box surface, for example. More than likely, you will find a pattern with those balls in relation to RG and differential. If you typically like higher RG balls, stick with higher RG balls, or vice versa. Know what specs fit your style of play. This will increase your chances of making sure that your new ball is suited for you.

Buying balls that look good for others is a common mistake. Selecting the right ball depends on many factors: ball speed, axis of rotation, rev rate, lane conditions and surface, and how you like to play the lane, for example. In selecting the proper equipment, the most important factor to consider is coverstock. This, followed by the proper core characteristics, will determine how soon or how late the ball will roll. From there, ball reaction is fine-tuned by the layout, which includes pin placement and mass bias considerations.

When you step up to the approach, you naturally hope to send your ball smoothly down the lane and into the pocket. But how hard should you throw it in order to achieve this goal? A shot that travels fast and hooks strongly across the lane often looks the most impressive, so it can be tempting to try to closely emulate the shots you see from professionals on TV or a high-scoring bowler that you face in your league. But knowledge of those factors as well as general guidelines can help you determine what is going to be the most effective speed for your own game.

First, the USBC and ball manufacturers have actually given some recommendations as to what ball speed is best, and their research indicates that 21 mph at the release is optimal which corresponds to 17 mph when it gets down the lane and hits the pins.

In particular, a faster shot will give you more pin action, but it will have less of a chance to react to the lane, which results in less hook.

On the other hand, a slower shot will hook more, but at the expense of some pin action.